- Fully floating 2-piece rotor that allows outer ring to expand freely in response to heat. This reduces stress which in turn extends rotor life and reduces the tendency for rotor cracking during extreme use.
- Drive bobbins machined from a single piece of stainless steel giving maximum strength and corrosion resistance. Stainless bobbins reduce the requirement for regular disc maintenance and ensures the outer ring continues to float freely even when used on the public road with corrosive salts and other road grime.
- Each bobbin assembly features an anti-rattle spring clip ensuring silent operation when driving on the public highway
- Rotor rings feature 48 directional internal curved vanes for improved rotor coolin
- Friction rings are cast from high carbon G3500 alloy giving excellent wear properties and improved thermal capacity. All EBC disc rings are cast using the ‘centre split’ casting method, ensuring a balanced casting that will not distort under high heat, an issue common with cheaper ‘moulded out’ castings.
- Unique Swept Groove slot design for effective evacuation of braking dust and gasses whilst ensuring good initial ‘bite’ on brake apply
- Replacement disc rings for EBC floating rotors are significantly less expensive than our major competitors.
Brake Vibration: Common Questions Answered
What is Brake Vibration?
Brake vibration is where a shaking motion occurs when the brakes in a car or other vehicle are deployed. This can vary from a slight shaking to a quite severe shuddering, depending on the severity of the condition. It can also be known as rotor shimmying or brake pulsation.
What causes it?
If the brake rotors installed on the vehicle have more than .05mm of run out (where the brake rotor moves from side to side more than a minimal amount of .05mm), then brake vibration will occur through the steering. Usually, this is due to one of two different reasons. The face of the disc may have some rust or dirt on it, which is causing the run out figure to be incorrect. Such build up may occur during the lifetime of the rotor, and this can cause the run out to be up to five times the limit installed by the factory. If the problem is not due to this, it may be that a ‘thin spot’ has occurred on the rotor (where there has been intermittent pad contact instead of a constant motion). When the brake pedal is pressed this causes the brake vibration to occur. This is technically known as Disc Thickness Variation, or DTV for short.
As it is essential that your brakes run true, this must be sorted out as quickly as possible.
How to rectify the problem
The first thing to do is to determine whether it is the front or rear rotors that are causing the brake vibration. If the steering wheel itself is shaking, it is more likely to be the front, whereas if the whole car and bodywork shakes, it will probably be the rear. Additionally, it is not necessarily the pair of rotors that are the problem; it may only be one of them. Finding the location of the shaking is the first step to solving the problem, however.
Depending on whether you undertake your own mechanical work, there are two routes to take here. Firstly, you can rectify the brake vibration yourself, or secondly, you can take the vehicle to a garage to resolve the issue. Either way, if the problem is a dirty disc surface, having the rotors turned or skimmed to present a clean, smooth surface to the brake pads can solve this. If the rotors have a thin spot, they will need to be replaced with new ones. Regardless of which method you choose, they must be checked when fitted back to the car that the run out is the correct measurement.
What to look for when choosing a garage to do the work
Firstly, ensure the garage you are looking at choosing is reliable – if you can get some recommendations from friends or family as well, this is always helpful. Also, make sure you have a chat with their mechanics and make sure their knowledge seems extensive enough; it is very important they know what they are doing. Competitive pricing is also going to be an issue, but cheapness does not always mean quality, so sometimes it may be better to choose a slightly more expensive option for better service.
On the same note, ensure if you are going to turn the rotors or fit new ones yourself, make sure you know what you are doing and don’t hesitate to call a garage if you get stuck or feel unsure. Safe braking is so important and it is imperative the work is done correctly and safely.